Tenere 700: Hwy Pegs Mounted to AXP Skid Plate

By

 Tenere 700 Hwy Pegs Mounted to AXP Skid Plate

I sourced these folding hwy pegs with rubber o-rings on the peg on Amazon.ca for $29.58 (did not use the tube mounts).



Was able  to mount to my AXP skid plate utilizing existing vent holes with the following hardware:
  • 21.2 mm diameter aluminum 4 mm thick wall tubing cut at approximately 30 degree angle on 1 end to use as spacers to allow for adjustable positioning of the pegs
  • four 8 mm x 30 mm button head allan bolts with nyloc bolts + blue loctite
  • eight 38 mm washers to mount to the skid plate
  • four 25.8 mm washers to mount pegs to the mount
  • two HD hwy peg mounting plates I had in a parts bin




Mounted to AXP skid plate using existing vent holes & HD hwy peg mounting plates from parts bin.


 

They are positioned to fold back & up about 45 degrees to minimize issues when riding off-road or dropping the bike. When folded in they are the same width as the outside tips of the shifter & foot brake lever.


 

They are positioned 34.3 mm or 13.5" forward of the rider pegs & from the ground.

 
 
Extended width is slightly wider than the Pivot Pegz Mk4 rider pegs & are angled slightly up & back for comfort & stable foot placement.

 

Comments

Post a Comment

Popular posts from this blog

Tenere 700: MIVV Dakar Exhaust & Carbon Heat Shield

By
Image
MIVV Dakar Y.064.LDKX Exhaust + Carbon Heat Shield ACC.80.0 Why a New Exhaust? Yamaha opted for Dakar inspired styling & cost savings vs function with the design & location of the oem muffler for the Tenere 700 that positions it precariously low & outside the swingarm, attached to a welded on vs bolt on hanger that easily bends pushing the muffler into the aluminum swingarm with the slightest provocation (there have even been reports that some damaged bikes in the USA have been written off by insurance citing a bent frame). See  my blog article here  for additional info on the swingarm/muffler issue & several aftermarket T7 exhaust options. The oem wide muffler positioning also complicates the use of some soft bag & rackless systems & clearance with the hot muffler plus mandates that many luggage rack systems be detrimentally far away from the center line of the bike,  adding unnecessary width & undesirable handling dynamics at the back end. De...
Read more

Tenere 700: 8 Day, 4,360 km (2,709 mile) 'Rideabout' - 2 Provinces, 5 States, 1 Provincial & 4 National Parks + Tenere 700 Hwy Touring Observations Aug 2024

By
Image
    8 Day,  4,360 km (2,709 mile), 'Rideabout' - 2 Provinces, 5 States, 1 Provincial & 4 National Parks -  Aug 7-14, 2024 With each year, & officially a 'baby' senior at 66, motivation & ability to do the things I historically treasured become a plethora of balancing the increasingly disparate physical & emotional realities with the seductive biased recollections of my youth touring much of western Canada & USA, Baja/Central/Northern Mexico & 2 years in Texas via motorcycle...Bob Seger's "Against the Wind' echoes in my head 😎.  After having to cancel my Yukon/Alaska trip this June because of recurring back issues, & while no where near 100%, was in need of some throttle therapy & seized an opportunity. The ensuing journey is as much an exploration of my current abilities for a concentrated high mileage solo 1 or 2 week long 'rideabout' without much conditioning & lead up riding as it is about my accessorized ...
Read more

Tenere 700: Correct Fork Alignment - Floating Right Fork Needs to be Set Correctly on Axle to Obtain Equal Gap for Brake Caliper & Rotor - Service Manual Front Wheel & Tightening Torques - 'Everything Tenere' & Dave Moss Videos: Align Fork Legs Properly After Mounting The Wheel

By
Image
Disclaimer: I am just a long time motorcycle enthusiast with moderate wrenching experience/skills (not a professional/Yamaha mechanic) & have compiled this info from others more experienced & knowledgeable as a reference based on my personal experience with my T7 that hopefully can help others. Fork Alignment & Right Fork Caliper/Rotor Position MUST Be Checked After Front Wheel Removal! T he T7 right front axle assembly is a floating design that, depending on several factors, may not correctly position the caliper & rotor for equal gap & can result in the rotor resting against the upper edge of the caliper...not a desirable situation if gone unnoticed. This information is NOT in the Yamaha Service Manual & can be an overlooked issue when changing the T7 front tire .. .the right fork's static/resting position is toward the outside on my T7, which incorrectly positions the inside edge of the caliper to make contact with the rotor ( has been posted by others ...
Read more